logo

Dsc pc 3000 programming manual. DSC PC3000 Keypad Instruction manual PDF View/Download

Dsc pc 3000 programming manual Rating: 7,5/10 799 reviews

DSC PC3000 INSTRUCTION MANUAL Pdf Download.

dsc pc 3000 programming manual

Then, with the system disarmed, activate all detection sensors one at a time and observe the zone light come on at the keypad as each sensor is activated. If the alarm is not acknowledged and the 30 second delay expires, the fire memory latches and the transmission cannot be aborted. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Easy to cancel your membership. The doors and windows which will provide this indication are programmed by your installer. Zone Light 3 Zone Light 4 Zone Light 5 Zone Light 6 Zone Light 7.

Next

Dsc pc2550 programming manual

dsc pc 3000 programming manual

Therefore if the system is armed and disarmed before the expiry of the exit time, no transmission will take place. When the correct code is entered and the system is armed, exit through the door indicated by your installer as the exit-entry door. Are furnaces and wood burning appliances properly installed, clean and in good working order? Only codes up to the last one entered will be changed. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security Controls Ltd. Revise the plan as conditions change; for example, when there are more or fewer family members in the home, or if there are changes to the house. Note: Codes 9 to 16 are always assigned to Group A.

Next

DSC PC3000 Keypad Instruction manual PDF View/Download

dsc pc 3000 programming manual

The zone alarm reporting codes must all be single digit numerical codes with no extended 2nd round being sent. When enabled the keypad buzzer will beep quickly 5 times each time any zone defined as a delay or instant circuit opens or closes. Programming this section tells the dialer whether to send transmissions to the 1st or 2nd telephone number. Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise locale de télécommunication. Be sure to remove snow from exterior patio doors in winter; outdoor furniture or equipment should not block exits.

Next

DSC PC3000 INSTRUCTION MANUAL Pdf Download.

dsc pc 3000 programming manual

It is necessary to program the format number for each telephone number even if the first phone number is the only one being used. Assist the user in working through examples of each type of command. When the system is armed using one of the access codes, the corresponding reporting code is transmitted. Exit the premises through the designated exit-entry door. The feature is automatically disabled when the panel is armed and disarmed. If the connection is made in the reverse the battery fuse will fail. L'indice de charge de cet dispositif est 42.

Next

Dsc Pc3000 Programming Manual Dsc Pc3000 Programming Manual PDF Download Free

dsc pc 3000 programming manual

Station 1 is telephone number 1. Write the plan down and rehearse frequently, so that should an emergency arise, everyone will know what they are to do. If not used, leave at the factory default settings. Provide user with the Instruction Manual and instruct them to read the manual to become familiar with the system operation. This feature operates only while the panel is disarmed. This allows the user to disarm the system preventing false alarms inside the premises.

Next

DSC PC3000 Control Panel Programming Manual

dsc pc 3000 programming manual

However, there is no guarantee that interference will not occur in a particular installation. The 8 two digit numbers entered correspond to zone definitions for zones 1 to 8. These zones may or may not be active on your keypads depending on how your installer has programmed them. The smoke from a fire generally rises to the ceiling, spreads out across the ceiling surface and begins to bank down from the ceiling. For additional access codes, see Programming Additional Access Codes.

Next

AlarmsBC presents user manual pc

dsc pc 3000 programming manual

Ensure that they are not painted shut, and that their locking mechanisms operate smoothly. When connecting sirens speakers with siren driver already built-in , be sure to observe the correct polarity. They also have entry delays provided that a delay zone has been tripped first. The feature is turned off if the keypad sounds one long beep. This command is used for arming the system while at home. Disarming Enter the premises through the designated exit-entry door. This booklet is available from the U.

Next

➤ Download Dsc Pc 3000 Programming Manual PDF E

dsc pc 3000 programming manual

If the bell fuse is blown or the bell circuit is open, a keypad trouble and a trouble transmission are generated. If a printer is attached to the panel, setting the clock must include the day, month and year. Printer only Printer and norm. Pull all cables into cabinet and prepare them for connection before mounting the circuit board to the back of the cabinet. Describe the basic keypad functions. If you are unsure about system operation, contact your installing dealer. All zones with an exit delay may be tripped during the exit delay without creating an alarm.


Next

DSC PC3000 INSTRUCTION MANUAL Pdf Download.

dsc pc 3000 programming manual

There are three zones which can be activated from the keypad. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100. Hex values or 00 are not allowed. Do not investigate first or attempt to fight the fire, and do not attempt to rescue belongings or pets as this takes up valuable time. Do not unintentionally bypass zones when arming.


Next

DSC PC3000 INSTRUCTION MANUAL Pdf Download.

dsc pc 3000 programming manual

Close all protected doors and windows and stop movement in areas covered by motion detectors. Fill out the work sheet and use it as a guide when programming. The disabled mode is useful if there are multiple downloading computers at different telephone numbers. All keypad entries are made by pressing one key at a time and may be changed by you at any time if the installer selects an option. Remember if no keypad entry is made for more than 2 minutes the keypad will return to the normal arm-disarm display and the complete command will have to be re-entered to program a new access code. There is no light annunciation from the keypad for the last two keypad zones, however, the keypad buzzer beeps 3 times to confirm activation on any of the keypad zones.

Next