logo

Tajima manual pdf. Tajima TMFX User Manual

Tajima manual pdf Rating: 6,7/10 821 reviews

Tajima TME, TMEF User Manual

tajima manual pdf

Cause Adjust Loose or broken belts Adjust the belt tension or replace the belt. The size of the hole is adjustable and the shape can be created through the process of digitizing to meet your desires. B03: Floppy is marked as read-only. In case of stitches less than 1. It describes about operation of the machine and items to notice for use. It is now possible to embroider a max. When it is possible to change setting, the operation button on the panel is displayed.

Next

Tajima TME

tajima manual pdf

Machine construction Operation panel box Operation panel box 1. Be sure that automatic color change has been activated. They can be installed from personal computer or floppy disk. Connect an external device and the machine using the cable. Important warning items for safe operation Warning labels. Design edit Repeat Repeat This setting repeatedly arranges design of which data is set.

Next

Manual Tajima

tajima manual pdf

P and one blinking light is normal. Basic operation Starting and stopping the machine Starting and stopping the machine 1. You could sustain severe injuries due to being entangles by moving machine units. If the E is blinking, then no color has been chosen yet. Fitting Screw Thread guide system support bar Remove the wind bolt and pull up the thread guide system support bar. Manual operation Offset setting for position Offset setting for position Set offset position. You are ready to start sewing! Spin the inner jog dial until a circle is displayed instead of a minus.

Next

Tajima TME, TMEF User Manual

tajima manual pdf

Machine construction Name of each part Name of each part 1. . Outline of functions Rotate Rotate This function rotates design of which data has been set. Repeat the process until all colors are programmed. Basic operation Inspections before starting operation Inspections before starting operation Before embroidering, execute inspections of the following items. Automatic offset Offset position This setting makes the frame move to the offset position automatically when embroidery is finished if offset position is set and offset of frame setting is set to auto.


Next

Tajima TMFX User Manual

tajima manual pdf

Machine construction Name of each part 2. The first memory location with a stitch file will display. Electro-component parts Power supply box. The design is rotated centering the design start position. The needle will change to the new location.

Next

Tajima TME, TMEF User Manual

tajima manual pdf

The needles should now move to the new color. C01: No response to floppy drive activation signal. It will ask for the type of head cards. Outline of functions Offset Offset This function makes the frame move to the position set by offset, and return the frame to the original position after working. Hold down F3 and turn on the machine at same time. Re-do this selection if you get false thread brakes continuously.

Next

Tajima TMFX User Manual

tajima manual pdf

Important warning items for safe operation Carrying. It will ask for number of needles. When detaching the table, do not lose the screw. Electro-component parts Controller card When you take off the cover, also disconnect the power supply harness from the controller card that is located at the cover. Check main shaft if it is bound. Tie stitching goes and returns in 0.

Next

TOKAI TEJTII

tajima manual pdf

Make sure your offset is programmed or cleared, or the frame will move where you don't expect. Will display C or a backwards C whenever you have gone past the last needle or before the first needle. Type in the desired number, or use the +1 -1 numbers to scroll through the selections. Setting value: Off, 1 Stitches of 1. It is now asking you to program the first color. The process will start from the first color. Bar Edit Machine Frame Data Selection Setting Setting Data Do not push the operation panel with a sharp-pointed object.

Next

Manual Tajima

tajima manual pdf

Error codes 211: Main shaft not at fixed position. Choose a design by typing in the number. Check color change needle position and manually move to proper position if needed. The needle for the current color will blink. The thread trim operation should activate now. Data set means to make design data possible to be embroidered. The reader will now start downloading, wait for completion.

Next